Key takeaways
- Pro: Aluminum construction is generally lighter than steel, which makes it easier to lift into the bed once the machine is loaded and strapped down.
- Pro: The folding format stores flatter than a rigid ramp, leaving room for coolers, fuel cans, and tie-downs in a crowded truck or garage.
- Con: Folding ramps have a hinge or seam, and that joint is the first place to inspect for wear, play, or bent edges.
A loaded ATV weighs several hundred pounds, and the few feet between the ground and a tailgate are where most back strains and tip-overs happen. A good loading system makes that climb gradual, keeps the tires on a gripping surface, and folds small enough to travel with you. For most owners that means a pair of aluminum ramps or a single folding ramp, matched to the truck or trailer they actually use rather than to a catalog photo.
The right choice depends on how you haul. A trailer with a low deck needs very little ramp, while a lifted pickup bed asks for length and arch. This guide compares six ramp-style options by brand and product type, explains the numbers that matter before you buy, and points out the trade-offs that follow from each product name. As of 2026 the basic physics has not changed: longer ramps mean gentler angles and fewer scraped skid plates.
Quick Picks
| Product | Best for | Worth knowing |
|---|---|---|
| Black Widow Aluminum Folding ATV Ramp | Owners who want a ramp that stores flat | Folding design trades a little rigidity for compact storage |
| Titan Ramps Aluminum Arched ATV Ramps | Loading into a tall pickup bed | Sold as a pair, so you need space for two ramps |
| Rage Powersports Aluminum Folding ATV Ramp | Single-ramp loading with a folding frame | One ramp means the machine has to be centered carefully |
| Erickson Folding ATV Loading Ramp | Occasional loading from a trailer or truck | Folding hinge is a point to inspect regularly |
| Kolpin ATV Loading Ramp | Riders who already use Kolpin racks and gear | Check the length against your tailgate height |
| Black Widow Aluminum Arched Dual Runner ATV Ramps | Riders who prefer two separate tire tracks | Dual runners need to be spaced to match the wheelbase |
How to Choose
Ramp length against loading height
A good rule of thumb is a ramp angle of 15 degrees or less. Measure from the ground to the tailgate or deck, then multiply that height by roughly four to get a comfortable ramp length. A 30 inch tailgate calls for about a 9 or 10 foot ramp, while a 20 inch trailer deck is fine with 6 or 7 feet. Short ramps on tall beds are the usual cause of bottoming out, spinning tires, and nervous riders who stop halfway up.
Weight rating with a safety margin
Look up the machine’s dry weight and add fuel, gear, and the rider if you plan to ride it up. Then pick a ramp rated for at least 1.5 times that total. Ratings are normally listed per pair, so a single folding ramp must carry the full load by itself. Do not assume a ramp sold for a sport quad can also handle a heavier utility machine or a side-by-side.
Width, tread, and rail design
ATV tires are typically 8 to 10 inches wide, so each runner should be at least that wide, or the ramp should be one full-width surface. Look for punched holes, ribbing, or a traction texture on the walking surface, and raised side rails that keep a tire from rolling off the edge. Smooth aluminum becomes slick when wet or muddy, so open-grip patterns are worth paying attention to.
Attachment and storage
Secure attachment matters more than any other detail. Check for a lip, hooks, or straps that lock onto the tailgate or bed rail so the ramp cannot kick out under load. For storage, folded length and weight decide whether one person can handle it. A fair rule of thumb is that anything you cannot lift alone will tend to stay in the garage when you actually need it.
Our Picks Reviewed
Black Widow Aluminum Folding ATV Ramp
6' 5" ATV Ramp, Loading Trailer, Folding, 1,500 lb Cap, Black Widow | Load four-wheelers into trailer, folds into thirds for storage, safety straps included
As an Amazon Associate we earn from qualifying purchases. Product prices and availability are accurate as of the date/time indicated.
This is a folding aluminum ramp from a brand known for powersports loading gear, built to cover the gap between the ground and a truck bed. The name tells you both the material and the format, and those two words shape the trade-offs below.
- Pro: Aluminum construction is generally lighter than steel, which makes it easier to lift into the bed once the machine is loaded and strapped down.
- Pro: The folding format stores flatter than a rigid ramp, leaving room for coolers, fuel cans, and tie-downs in a crowded truck or garage.
- Con: Folding ramps have a hinge or seam, and that joint is the first place to inspect for wear, play, or bent edges.
Skip it if you want the stiffest possible surface for a very heavy machine, or if your loading height is tall enough that you need long dual runners for a gentle angle.
Titan Ramps Aluminum Arched ATV Ramps
Titan Ramps Aluminum ATV Loading Ramps, 1,200 lb, 10 Ft, 2-Pack | Lightweight Foldable Ramps with Serrated Crossbars for Traction, Arched for Clearance, Safety Straps for Pickup Trucks
As an Amazon Associate we earn from qualifying purchases. Product prices and availability are accurate as of the date/time indicated.
Titan Ramps focuses on aluminum ramps, and this listing is a pair of arched ATV ramps. Arching is meant to reduce the sharp transition at the top where a low frame or skid plate can scrape the tailgate edge.
- Pro: A pair of runners lets each tire have its own track, which many riders find steadier than steering up a single narrow ramp.
- Pro: The arched shape suits taller pickup beds, because a curve eases the break-over point near the tailgate where most scraping happens.
- Con: Two separate ramps take more storage room and must be spaced to match your wheelbase every single time you load.
Skip it if you load from a low trailer, since a long arched pair is more ramp than you need, or if you want one fast grab-and-go piece for solo loading.
Rage Powersports Aluminum Folding ATV Ramp
Rage Powersports sells loading and tie-down equipment, and this is a folding aluminum ATV ramp. Like other single-piece folding designs, it favors convenience and quick setup over the extra margin that a dual-runner pair offers.
- Pro: A single folding ramp is quick to set up, with only one attachment point to line up and strap down before the climb.
- Pro: Aluminum keeps the carry weight below what a comparable steel ramp would be, which helps anyone who loads and unloads alone.
- Con: With one ramp the tires share a single surface, so alignment mistakes show up quickly and the margin for error is smaller.
Skip it if you are new to loading and nervous about steering, since two separate runners can feel more forgiving. Also skip it if you move a heavy utility machine regularly.
Erickson Folding ATV Loading Ramp
Erickson makes cargo management products, and this name points to a folding ramp aimed at ATV loading. It sits in the practical middle ground for occasional haulers who load a few times each season rather than every weekend.
- Pro: A folding format means it can ride in the bed or along a trailer fender without needing a dedicated rack or storage bracket.
- Pro: Purpose-built ATV sizing usually means a surface wide enough for typical quad tires, unlike a generic utility ramp meant for lawn mowers.
- Con: Folding joints add moving parts, so regular checks of hinges and latches should be part of every trip.
Skip it if you need a very long ramp for a tall lifted truck, or if you want a premium pair of arched runners and are willing to carry the extra bulk.
Kolpin ATV Loading Ramp
Kolpin is a long-standing name in ATV racks, mounts, and accessories, and this is a loading ramp from that lineup. Brand familiarity and a clear ATV focus are the main draws, rather than any single headline feature.
- Pro: Buying from an accessory brand that concentrates on ATVs makes it easier to find matching straps, racks, and replacement parts later.
- Pro: A dedicated ATV ramp is sized with quad-style tires in mind, which beats improvised planks or a general-purpose ramp.
- Con: The name does not state length or capacity, so you must confirm both against your truck height and machine weight yourself.
Skip it if you cannot verify the weight rating before buying, or if you plan to haul a larger machine than a standard sport or utility quad.
Black Widow Aluminum Arched Dual Runner ATV Ramps
Black Widow 10' ATV Ramps, Folding, for Truck or Trailer | Dual runner ramps for quads, four wheelers
As an Amazon Associate we earn from qualifying purchases. Product prices and availability are accurate as of the date/time indicated.
Another Black Widow option, this one named as arched dual runners. The wording suggests two separate tracks with a curved profile, a layout many riders associate with taller truck beds and heavier machines.
- Pro: Dual runners give each side of the machine its own track, which tends to feel more stable when you are riding the quad up under power.
- Pro: The arched profile helps soften the transition at the tailgate, reducing the chance of the frame catching on the edge.
- Con: Two runners need to be lined up, spaced, and strapped separately, which adds setup time compared with one folding ramp.
Skip it if you want the quickest possible solo setup, or if storage is so tight that two long runners will not fit across the bed or in a closet.
Which One Fits
- Tall pickup bed: the Titan Ramps arched pair or the Black Widow dual runners, because curve and length help the most at height.
- Solo loader with limited storage: the Black Widow or Rage Powersports folding ramps for quick setup.
- Trailer with a low deck: the Erickson folding ramp is usually plenty.
- Rack-and-accessory shoppers: the Kolpin ramp fits neatly into a system built around the same brand.
- Heavy utility machines: prioritize ratings and runner width over convenience, and lean toward a dual-runner pair.
Common Mistakes
- Buying a ramp that is too short for the tailgate height, leaving a steep angle that scrapes the frame.
- Ignoring the total weight, including fuel, gear, and rider, when comparing against the ramp rating.
- Skipping straps or hooks, so the ramp can slide off the tailgate mid-climb.
- Loading on soft or sloped ground that tilts the ramp sideways and pushes a tire toward the edge.
- Forgetting that wet or muddy tires can slip on smooth aluminum, and not cleaning them before the climb.
FAQ
How steep should an ATV loading ramp be?
Aim for 15 degrees or less. In practical terms, divide the loading height by four to estimate the minimum ramp length in the same unit.
Is one ramp enough or do I need a pair?
Either works if the rating covers the load. A pair is easier to steer onto, while a single folding ramp is faster to store and set up.
Do I need a special ramp for a heavier machine?
Yes. A larger utility ATV or side-by-side needs a higher rating and a wider surface, so check those figures before you rely on a lighter ramp.
What else shares the truck bed with the ramps?
Camping gear often does. Riders who also tow or carry a shell may want to browse truck campers to see how bed space and payload get divided up on long trips.
Does cabin comfort matter on long hauls to the trail?
It does, because the drive is often hours long. Many riders add one of the lumbar support cushions for car seats to reduce fatigue before they even unload the quad.
Worth a look next